Hi,
if I try a short test the HDD switched off until a new power off/on.
--------------------
address@hidden smartctl -t short /dev/sda -d ata
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately
in off-line mode".
Drive command "Execute SMART Short self-test routine immediately in
off-line mode" successful.
Testing has begun.
Please wait 1 minutes for test to complete.
Test will complete after Tue Sep 23 09:05:36 2008
Use smartctl -X to abort test.
address@hidden date
--------------------
'smartctl -a /dev/sda -d ata' show the following:
---------------------------------------------------------
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3750330NS
Serial Number: 9QK15775
Firmware Version: SN05
User Capacity: 750,155,292,160 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Tue Sep 23 09:25:51 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data
Collection: Enabled.
Self-test execution status: ( 41) The self-test routine was
interrupted
by the host with a hard or
soft reset.
Total time to complete Offline
data collection: ( 625) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection
upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 168) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Interrupted (host reset) 00%
58 -
# 2 Short offline Interrupted (host reset) 00%
57 -
# 3 Short offline Interrupted (host reset) 00%
38 -
# 4 Extended offline Interrupted (host reset) 00%
33 -
# 5 Short offline Completed without error 00%
0 -
# 6 Short offline Interrupted (host reset) 00%
0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
---------------------------------------------------------
My questions:
1) is it a bug?
2) what can I do?
3) by the way: is my HDD OK (Seek Error Rate)?
Best Regards!
Konrad